Eco-friendly, non-polluting and zero-emission fermentation beds raise chickens. It sounds magical. Is it complicated to do it? What kind of preparation is needed?
First, the preparation of fermentation bed chicken technology
The site selection of chickens in dry-fermented-bed fermentation chickens: The site of the chicken farm should be located in a place with high topography, dry and flat, well-drained and sunny. At the same time, it is advisable that the groundwater level should be low, which should be less than 1.5m below the foundation of the building. Sites such as near rivers, lake waves, etc., should be selected at higher addresses, which is 2 meters higher than the highest level of local hydrological data.
On the water quality of the water source should be better, electricity, and convenient transportation, away from the major traffic trunks, villages, schools, slaughter
Field, veterinary station.
Technical design of the chicken house:
The height of the quail dry-sweeping broiler house is generally 2.5-3.5m, the span is 9-13 meters, the length can be flexibly controlled according to the breeding quantity and terrain, and can also be taken from the greenhouse, the top design vent, the top The use of composite color steel tile, etc., the roof of the house and the wall can be used in the case of a dedicated skeleton support, all the use of composite foam sheet, this has the advantage of low cost, good insulation effect, construction and construction fast, the overall requirement is winter insulation, Insulation in summer. Can be designed to be fully enclosed, the design should be equipped with axial fan plus wet curtain, it can also be designed to be fully open, in winter with plastic film plus insulation curtain, full open in summer to facilitate ventilation and cooling. In order to ensure ventilation, doors and windows should be enlarged as much as possible. If a roller blind is installed, it can be designed and manufactured on its own, but it is better to purchase a special roller blind. At present, there are roll shade products that are used in conjunction with the fermentation beds by manufacturers. This kind of roller blind has high material strength, is light and open and closed, and has rope support. It can still be used effectively in bad weather such as strong winds and storms. Open the ventilation holes (ground windows) at the skylight and at the base of the wall. The sunroof should be installed at the highest point of the roof, and it is better to be above the midline of the house. Each room should have a ground window, each about 25 centimeters by 25 centimeters. It is also possible to build multiple small ground windows per room with the total area approximately constant. The height of the lower window is about 15 cm above the surface of the fermented mattress material. Excessively affecting the rise of hot and humid gas on the ground. If the temperature is too low, it may cause rainwater to enter the house. To prevent rainwater from entering the house, a flip-type baffle plate may be installed on the ground window. Designed drinking facilities and feeding facilities. There is no need to design a pedestrian walkway in the sheds. People can walk on the litter and save the area within the shed, thus increasing the shed utilization rate.
In summary, it can be seen that the difference between the design of a chicken house in a dry-sweeping fermentation bed and that of an ordinary chicken is not large, and there is no need for additional construction investment, but the height of the chicken house is increased. That is, it cannot be too low, because there is an increase of 40cm of litter. You can also take the form of litter pool, but you must ensure that surface water can not enter the room, affecting the litter moisture. The materials and quantity required for the fermentation bed: The choice of litter materials The purpose of the litter production is to ensure the vigorous growth of the fermenting strains. It is actually a good medium for the fermenting bacteria. Therefore, the raw materials should be selected in the litter production. The following conditions: can provide adequate carbon and nitrogen nutrition for fermenting bacteria. The carbon source is the energy basis for the growth and reproduction of bacteria, and the nitrogen source is the basic material for bacterial growth and propagation of synthetic bacterial proteins. The choice of raw materials should pay attention to the safety of raw materials, air permeability, water retention. Insulation: The temperature above 30°C is conducive to the growth and reproduction of the fermentation bacteria. This requires that the litter layer has a certain thickness. If it is too thin, it cannot be insulated, the bacterial growth is poor, and the fermentation effect is not good. Excessive thickness causes waste. The thickness of 40-50cm creates favorable conditions for the growth and propagation of broth, thus providing a warm and comfortable environment for the healthy growth of chickens. Comfortable environment. Details can be consulted: Beijing Huaxia Kangyuan Technology Co., Ltd. Tel Free Hotline Taobao Buy Click
Read more:
Chickens in fermented bed in summer can effectively prevent chicken intestinal diseases
Fermentation bed breeding principle of constant temperature
Shock Wave Therapy Device,Shock Wave Therapy,Shock Wave Therapy Equipment,Shock Wave Therapy Therapy Machine
Puyang Degren Medical Equipment Co., Ltd. , https://www.degrenyuwei.com