Honey Pill Making Machine Introduction:
Honey Pills can produce honey pills, concentrated pills, water pill, water pills, pellets , and can also be coated and dried. Make the prepared pills even and beautiful. It is especially suitable for small pharmaceutical factories, large and medium-sized pharmaceutical factory trial rooms, Chinese medicine research institutes, hospitals, private clinics, Chinese medicine stores, and valuable tonic products on-site processing and sales points. The whole machine is made of stainless steel and conforms to GMP standards. And the small size, low power consumption, high efficiency, low noise, pollution-free, simple, safe and reliable, this machine uses 220V electric lighting, for the convenience of taking the electrode.
Honey Pills Pilling Machine Technical Parameters:
1. Function range: It can produce honey pill, concentrated pill, water pill, water pill, coating, drying and pelletized food.
2 , pelleting specifications: Φ4mm, Φ6mm, Φ8mm (optional two specifications).
3 , production capacity: 2-7kg / h (based on Φ6mm).
4 , motor output power: voltage: 220V, 50HZ; host power: 0.18KW, electric heating power: 1KW, motor speed: 1440 rev / min, working speed: 50 rev / min.
5. Scope of application: Applicable to small pharmaceutical factories, large and medium-sized pharmaceutical factory trial rooms, Chinese medicine research institutes, Chinese medicine research institutes, hospitals, private clinics, Chinese medicine stores (rooms), tonic sales counters on-site processing and food factory pellets Development and other units.
6 , dimensions: 550 × 330 × 250mm.
7 , machine weight: 35kg.
8. Structure: The machine consists of a squeezer, a pelletizing roller, a water pill coating device, a full gear variable speed motor, and electric heating.
9 , technical characteristics:
(1) Multi-purpose machine, easy to remove and wash; (2) Small in size; (3) Light in weight; (4) Stable in performance; (5) Easy to operate; (6) Easy to clean; (7) Power-saving safety; ) low noise; (9) beautiful appearance; (10) all parts in contact with the drug and the outer casing are made of stainless steel, in line with GMP standards.
Honey Pills Machine Instructions :
First, the machine instructions
  1. Before using the machine, remove the upper cover and the gear cover. A few drops of non-hydrated edible oil must be added to each oil eye, and then scrub the four rollers and the parts in contact with the pill with medical alcohol. Disinfection treatment.
2 , the upper cover, the gearbox cover is reinstalled and reset, the power is turned on, the switch is turned on, and the empty machine is rotated for 1-2 minutes.
3. The uniformed pellets will be dispensed, put into the extruder in an appropriate amount, and stripped, and then the strips will be placed into the pellets one by one and directly into pellets.
4 , coating: After the pill is made, it can be placed in a water pill coating machine, wrapped in white, red and other outerwear.
5 , drying method: After the pill is made, the pill can be dried by entering the water pill coating device for electric heating. It can also be dried by the hot air of the hair dryer, or dried directly in the sun.
6. Polishing method: Put the pill in the water pill coating machine and roll continuously. The longer the rolling time, the smoother the surface.
Second, the user notice
 1. This machine is suitable for ambient temperature of -5 ° C to 40 ° C, relative humidity less than 90%. There is no conductive dust and corrosive metal gas around, and it is placed in a ventilated and clean place.
2. When operating, there should be no other unrelated items on the work surface. The pelletizing machine is placed on a stable table. When the power supply voltage is confirmed, the power supply should be close to the table. The power socket must have a reliable grounding wire. It is strictly forbidden to pull the power cord hard to prevent the person from tipping over and breaking the pill. Machine and other accidents occurred.
3. After the machine is used, remove the hexagon socket head cap screws, open the upper and lower parts with the roller as the boundary, remove the four rollers, scrub with medical alcohol, and then install the reset.
4. When scrubbing with medical alcohol, when changing the pelletizing roller, the total power must be cut off and the power plug must be pulled out to avoid personal accidents.
5. When the pelleting machine is in use, it is strictly forbidden to touch the pelletizing roller with hand and brush or other tools to avoid pinching the finger. It is strictly forbidden to process the pellets under the protection of the upper cover and the gearbox cover. An unnecessary personal accident has occurred.
6. If the power cord is damaged (such as exposed bare wires), you must use a dedicated power cord. Go to the local office maintenance department to purchase replacement. In case of failure of the switch or socket, it must be stopped. It is strictly forbidden to change the line to continue to use. The opening or socket of the same specification should be replaced in time to avoid mechanical and personal accidents.
7. The crushing equipment for this machine can be selected from our LH-08B flowing water Chinese medicine crusher or XFB-400g to 500g swinging Chinese medicine crusher.
8. The water pill coating can be directly removed and washed when not in use. Rotate clockwise and pull it out. Place it in a reliable, clean place for use. Apply a small amount of clean, anhydrous cooking oil to the exposed part of the water pill to prevent rust. It is strictly forbidden to wash the whole machine or electric heater directly with water. When the unit is not in use, it must be placed in a dry, clean and ventilated place. During the use of electric heaters, it is strictly forbidden to contact with water to prevent electrical conduction and cause personal accidents such as electric shock.
Third, machine parts
name        Weigh | regulation           grid | Number of accessories | Prepare    Note |
Heating plate | 80 × 105mm, 1KW | 1 | |
power cable | 0.75mm 2×1.8M | 1 | |
1.5mm 2×1.8M | 1 | |
Support      plate | 27cm×20cm | 1 | Daily necessities |
Water sprinkler | 0.5 kg | 1 | Daily necessities |
Â
Â
Fourth, the common causes of the pill machine failure and troubleshooting methods
Common faults of this machine | Production   Health   original   because | row    except    square    law |
You must be cut off in order to do the following |
1. After the unit is powered on , the motor does not run. | 1. Poor contact of the power cord or loose power plug; 2. Poor contact of the switch. | 1. Repair the power supply or exchange the plug of the same specification; 2. Repair or replace the same size switch. |
2. When the mechanism is pill , the shaft knife rotates or the medicine surface sticks. | Discharging loose baffles, and the knife shaft zui generated from the bottom, from the pills can not be scraped off axis knife slot. | Adjust to the distance between the discharge plate and the bottom of the shaft sipe , (about 0.1mm ) and tighten the set screws. |
3. When the unit is working , the motor stops suddenly. | 1. Capacitance is broken. 2 , the gear is stuck. | Check the gear slots for debris and clean them. |
4. When the machine is working , the shaft cutter has a slight jump. | Loose block screw loose | Open the cover, the inner hexagon screw 6 tightened evenly. |
5, the machine during operation, abnormal noise is generated. | 1. The shaft knife and the friction part of the machine body are dry and oil-free; 2. There is no oil between the gears. | 1. Inject a few drops of clean cooking oil into the oil eye; 2. Apply a small amount of butter to each gear groove. |
6 , the heater fails to heat up. | 1. The plug is loose or the power cord is off; | Replace the plug of the same specification or repair the power socket; |
Five, high pressure machine
The company's plodder, using high-quality refined materials, clean appearance, reliable quality, the use of lightweight, easy to carry.
Sixth, the operation method:
1. Loosen the adjusting screw 1 Move the movable leg 2 to use the size of the pot.
2. Lower the rack 3 to the bottom position of the zui , so that the indenter touches the panel and locks the limit nut 4 to avoid the over-position of the end of the pressing surface.
3. With the pressure bar 5 in the position shown , turn the handle 6 to raise the rack 3 to the high position of the zui.
4. Use the dough tube 7 to the dotted line position to load the pressed material.
5. After the pressed material is installed, move it back to its original position.
6. Turn the handle 6 so that the rack 3 is lowered to the material to be pressed without a gap.
7, hold the handle 6, without reverse gear, lever 5 swings up and down can be suppressed.
8. Rotate the part number 8 to clean the face tube and panel.
If you want to know more about the Pills Pilling Machine , please log in to our company :< > Or direct pharmaceutical technology department : <> consulting, our factory will provide you with more professional services!
Vc Enzyme Whitening Moisturizing Hand Cream, Skin nourishing hand cream. Rich in glycerin (4%) and vitamin E, light texture, nourish, and protect the hand skin softening, resistance to the daily invasion of loss for the skin with subtle aroma. Lightweight, easy to put in a handbag or travel. Use daily take appropriate massage your hands. Everyday care, can apply simple; in the fall and winter seasons, can also be coated with a gloved hand to fall asleep after a thick layer of hand cream, the second day, your hands must be smooth and moist, like a silky soft
Companies registered capital of 35 million yuan, the end of 2014 the total assets of 48.69 million yuan, including fixed assets of 37.52 million yuan. The company's existing cooperation Orange cultivation base 7043.5 acres, the company production base is located in Jiangxi County Tech Industrial Park Chu Tan industrial area, covers an area of 120 acres, it has built a standard plant 9,000 square meters, Nissan 6000 kg Orange enzymes and other liquid enzyme products. Enzyme, known as enzyme, refers to a polymer substance having biocatalytic functionality. In the catalytic reaction system an enzyme, the reactant molecules are known as substrates, enzyme substrates by catalytic conversion to another molecule. Almost all cellular activity of enzymes involved in the process are required to improve efficiency. Similar to other non-biological catalysts, enzymes chemical reactions by lowering the activation energy to accelerate the rate of the reaction, most of the enzyme catalyzed reaction rate can be increased a million times; in fact, the enzyme is to provide an activation energy needs than another low way, so that more particles to have less than the activation energy of the reaction kinetic energy, thus speeding up the reaction rate. Enzyme as a catalyst, in itself is not consumed during the reaction, it does not affect the chemical equilibrium reactions. Positive enzyme catalysis, but also a negative catalytic effect, not only to accelerate the reaction rate, but also to reduce the reaction rate. And other non-living catalysts is different, having a high degree of specificity of enzyme, only a catalytic reaction or produce a particular specific configuration.
Vc Enzyme Whitening Moisturizing Hand Cream
Vc Enzyme Moisturizing Hand Cream,Vc Enzyme Whitening Hand Cream,Rich Vitamin E Hand Cream,Nourish Enzyme Hand Skin Protection
Ganzhou Green days Biochemical Technology Co., Ltd. , https://www.tlqcjs.com